DAR File No. 31694

Natural Resources, Water Rights

R655-4

Water Well Drillers

NOTICE OF PROPOSED RULE

DAR File No.: 31694
Filed: 07/11/2008, 11:49
Received by: NL

RULE ANALYSIS

Purpose of the rule or reason for the change:

The Division of Water Rights needs to amend the administrative rule for Water Well Drillers (Rule R655-4) in order to conform to changes made in the Water Rights Law, Title 73, Chapter 3, by S.B. 228 (Regulation of Wells) during the 2008 legislative session. The Water Well Amendments in S.B. 228 gave the state engineer the authority to impose administrative fines for repeated noncompliance of the well drilling rules. In conjunction with the required changes to the rules needed to conform with the statute, other changes have also been proposed for the purpose of rule clarification and reorganization to eliminate confusion or to make them more succinct, equitable, and protective of groundwater resources. (DAR NOTE: S.B. 228 (2008) is found at Chapter 282, Laws of Utah 2008, and was effective 05/05/2008.)

Summary of the rule or change:

The revisions pertain not only to the statute changes related to administrative fines but also to other parts of the administrative rule for Water Well Drillers that require modification and clarification. Revisions involve the following items, which are summarized in this section. The State Engineer's Office has long struggled with what level of enforcement to impose on drillers with major or repeating violations of the well drilling rules. The current enforcement actions available to the State Engineer include: 1) no action; 2) probation; 3) suspension, and 4) revocation. The State Engineer's Office is reluctant to suspend or revoke a license only in the most extreme situations. The resulting enforcement action then in many cases is probation, which includes closer scrutiny with little to no penalty. As a result, violations tend to continue because there is no fear of any significant action being taken against a driller license. The administrative fine would allow the State Engineer to have an intermediate enforcement alternative between probation and suspension, which would better serve to deter major and/or repeated violations. Fines for minor infractions would not be levied until the violation was repeated during or after a probationary period. For major infractions, administrative fines could be levied for first offenses. In either case, fines would not be levied until after a hearing is held. The proposed administrative fine structure has been incorporated into the infraction/enforcement section of the well drilling rule (Section R655-4-5). Because the well drilling rule must be revised as per the new statute changes, there is an opportunity to update, clarify, and/or revise other sections of the well drilling rule as needed. Proposed revisions of the well drilling rule are related to the following topics: 1) clarification on the type of wells and activities that are regulated by the well drilling rule; 2) clarification of the amount and type of experience needed to obtain a well driller's license; 3) requirement to update the start date on a start card if a project is delayed; 4) clarification on conditions for issuing a cease and desist order; 5) update of steel casing standards; 6) clarification of interval seal requirements to avoid aquifer commingling and cross contamination; 7) update of the disinfection requirements to conform with the latest technology and industry standards; 8) update of pitless adapter requirements; and 9) general wording and grammatical clarifications and revisions.

State statutory or constitutional authorization for this rule:

Section 73-3-25

Anticipated cost or savings to:

the state budget:

There will be no budgetary changes required as a result of this rule revision. The changes can be implemented using existing staff and resources. Other rule changes simply provide clarification and will not increase staff efforts or costs. The proposed amendments will result in minimal costs to reprint the rule once the amendments are made effective. The penalties collected will create a small fund to be used for improving well driller education and infraction investigation and enforcement.

local governments:

There is no impact to local government because they are not involved in the regulation of water well drillers.

small businesses and persons other than businesses:

The proposed amendments do not apply to a small business or other persons except as a small business or other person may be alleged to have violated a pertinent statute or rule. In that case, compliance costs or savings would be as described for affected persons below.

Compliance costs for affected persons:

The proposed substantive amendments to the well drilling-related rules, enforcement, fines, and penalties apply only to persons alleged to have violated statutes and rules in specific circumstances. For some persons, depending on the facts pertaining to the alleged violation, a monetary penalty may be calculated. It is difficult to foresee the number and amount of fines imposed, which will depend on repeated noncompliance with the rules.

Comments by the department head on the fiscal impact the rule may have on businesses:

The revisions to these rules should have no impact on businesses other than the administrative fines that would be levied against water well drillers for failure to comply with the administrative rules and water well construction standards. Michael Styler, Executive Director

The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:

Natural Resources
Water Rights
1594 W NORTH TEMPLE
SALT LAKE CITY UT 84116-3154

Direct questions regarding this rule to:

Kaelyn Anfinsen at the above address, by phone at 801-538-7370, by FAX at 801-538-7442, or by Internet E-mail at KAELYNANFINSEN@utah.gov

Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

09/02/2008

This rule may become effective on:

09/09/2008

Authorized by:

Jerry Olds, Director

R655. Natural Resources, Water Rights.

R655-4. Water Well Drillers.

R655-4-1. Purpose, Scope, and Exclusions.

1.1 Purpose.

These rules are promulgated pursuant to Section 73-3-25. The purpose of these rules is to assist in the orderly development of underground water; insure that minimum construction standards are followed in the drilling, construction, deepening, repairing, renovating, cleaning, development, and abandonment of water wells and other regulated wells; prevent pollution of aquifers within the state; prevent wasting of water from flowing wells; obtain accurate records of well construction operations; and insure compliance with the state engineer's authority for appropriating water.

All administrative procedures involving applications, approvals, hearings, notices, revocations, orders and their judicial review, and all other administrative procedures required or allowed by these rules are governed by R655-6 "Administrative Procedures for Informal Proceedings Before the Division of Water Rights".

1.2 Scope.

The drilling, construction, deepening, repair, renovation, replacement, cleaning, development, or abandonment of the following types of wells is regulated by these administrative rules and the work must be permitted by the Utah Division of Water Rights and completed by a licensed well driller. These rules apply to both vertical, angle and horizontal wells if they fall within the criteria listed below. The rules contained herein pertain only to work on the well itself. These rules do not regulate the incidental work around the well such as pump and motor installation and repair; plumbing, electrical, and excavation work up to the well; and the building of well enclosures unless these activities directly impact or change the construction of the well itself. The process for an applicant to obtain approval to drill, construct, deepen, repair, renovate, clean, develop, abandon, or replace the wells listed below in 1.2.1, 1.2.2, [or ]1.2.3, and 1.2.4 is outlined in Section R655-4-7 of these rules.[ The process for an applicant to obtain approval to construct, deepen, repair, clean, or replace the wells listed below in 1.2.4, 1.2.5, or 1.2.6 is outlined in Appendix 1.]

1.2.1 Cathodic protection wells which are completed to a depth greater than 30 feet.

1.2.2 Heating or cooling exchange wells which are greater than 30 feet [or greater ]in depth and which encounter formations containing groundwater. If a separate well or borehole is required for re-injection purposes, it must also comply with these administrative rules.

1.2.3 Monitor, piezometer, and test wells designed for the purpose of testing and monitoring water quality and quantity which are completed to a depth greater than [of ]30 feet[ or greater].

1.2.4 Other wells (cased or open) which are completed to a depth greater than 30 feet that can potentially interfere with established aquifers such as wells to monitor mass movement (inclinometers), facilitate horizontal utility placement, monitor man-made structures, house instrumentation to monitor structural performance, or dissipate hydraulic pressures (dewatering wells).

1.2.5[4] Private water production wells which are completed to a depth greater than [of ]30 feet[ or greater].

1.2.6[5] Public water system supply wells.

1.2.7[6] Recharge and recovery wells which are drilled under the provisions of Title 73, Chapter 3b "Groundwater Recharge and Recovery Act" Utah Code Annotated.

1.3 Exclusions.

The drilling, construction, deepening, repair, renovation, replacement, cleaning, development, or abandonment of the following types of wells or boreholes are excluded from regulation under these administrative rules:

1.3.1 Any wells described in Section 1.2[cathodic protection wells, heating or cooling exchange wells, monitor wells and water production wells] that are constructed to a final depth of [less than ]30 feet or less. However, diversion and beneficial use of groundwater from wells at a depth of 30 feet or less[less than 30 feet deep] shall require approval through the appropriation procedures and policies of the state engineer and Title 73, Chapter 3 of the Utah Code Annotated.

1.3.2 Geothermal wells. Although not regulated under the Administrative Rules for Water Well Drillers, geothermal wells are subject to Section 73-22-1 "Utah Geothermal Resource Conservation Act" Utah Code Annotated and the rules promulgated by the state engineer including Section R655-1, Wells Used for the Discovery and Production of Geothermal Energy in the State of Utah.

1.3.3 Temporary exploratory wells drilled to obtain information on the subsurface strata on which an embankment or foundation is to be placed or an area proposed to be used as a potential source of material for construction.[

1.3.4 Wells or boreholes constructed to monitor man-made structures, house instrumentation to monitor structural performance, or dissipate hydraulic pressures on structures provided the wells or boreholes do not interfere with established aquifers or their primary purpose is not for monitoring water quality.]

1.3.4[5] Wells or boreholes drilled or constructed into non-water bearing zones or which are [less than ]30 feet or less in depth for the purpose of utilizing heat from the surrounding earth.

1.3.5[6] Geotechnical borings drilled to obtain lithologic data which are not installed for the purpose of utilizing or monitoring groundwater, and which are properly sealed immediately after drilling and testing.

1.3.6 Oil, gas, and mineral exploration/production wells. These wells are subject to rules promulgated under the Division of Oil, Gas, and Mining of the Utah Department of Natural Resources.

 

R655-4-2. Definitions.

ABANDONED WELL - any well which is not in use and has been sealed[filled] or plugged with approved sealing materials so that it is rendered unproductive and will prevent contamination of groundwater. A properly abandoned well will not produce water nor serve as a channel for movement of water from the well or between water bearing zones.

AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) - a nationally recognized testing laboratory that certifies building products and adopts standards including those for steel and plastic (PVC) casing utilized in the well drilling industry. ANSI standards are often adopted for use by ASTM and AWWA. Current information on standards can be obtained from: ANSI, 1430 Broadway, New York, NY 10018.

AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) - an independent organization concerned with the development of standards on characteristics and performance of materials, products and systems including those utilized in the well drilling industry. Information may be obtained from: ASTM, 1916 Race Street, Philadelphia, PA 19013.

AMERICAN WATER WORKS ASSOCIATION (AWWA) - an international association which publishes standards intended to represent a consensus of the water supply industry that the product or procedure described in the standard will provide satisfactory service or results. Information may be obtained from: AWWA, 6666 West Quincy Avenue, Denver CO 80235.

ANNULAR SPACE - the space between the outer well casing and the borehole or the space between two sets of casing[inner well casing and the outer well casing or borehole].

AQUIFER - a porous underground formation yielding withdrawable water suitable for beneficial use.

ARTESIAN AQUIFER - a water-bearing formation which contains underground water under sufficient pressure to rise above the zone of saturation.

ARTESIAN WELL - a well where the water level rises appreciably above the zone of saturation.

BENTONITE - a highly plastic, highly absorbent, colloidal swelling clay composed largely of mineral sodium montmorillonite. Bentonite is commercially available in powdered, granular, tablet, pellet, or chip form which is hydrated with potable water and used for a variety of purposes including the stabilization of borehole walls during drilling, the control of potential or existing high fluid pressures encountered during drilling below a water table, well abandonment, and to provide a seal in the annular space between the well casing and borehole wall.

BENTONITE GROUT - a mixture of bentonite and potable water specifically designed to seal and plug wells and boreholes mixed at manufacturer's specifications to a grout consistency which can be pumped through a pipe directly into the annular space of a well or used for abandonment. Its primary purpose is to seal the borehole or well in order to prevent the subsurface migration or communication of fluids.

CASH BOND - A type of well driller bond in the form of a certificate of deposit (CD) submitted and assigned to the State Engineer by a licensed driller to satisfy the required bonding requirements.

CASING - a tubular retaining and sealing structure that is installed in the borehole to maintain the well opening.

CATHODIC PROTECTION WELL - a well constructed for the purpose of installing deep anodes to minimize or prevent electrolytic corrosive action of metallic structures installed below ground surface, such as pipelines, transmission lines, well casings, storage tanks, or pilings.

CONFINING UNIT - a geological layer either of unconsolidated material, usually clay or hardpan, or bedrock, usually shale, through which virtually no water moves.

CONSOLIDATED FORMATION - bedrock consisting of sedimentary, igneous, or metamorphic rock (e.g., shale, sandstone, limestone, quartzite, conglomerate, basalt, granite, tuff, etc.).

DEWATERING WELL - a water extraction well constructed for the purpose of lowering the water table elevation, either temporarily or permanently, around a man-made structure or construction activity.

DISINFECTION - or disinfecting is the use of chlorine or other disinfecting agent or process approved by the state engineer, in sufficient concentration and contact time adequate to inactivate or eradicate bacteria such as coliform or other organisms.

DRAWDOWN - the difference in elevation between the static water level and the pumping water level[s] in a well.

DRILL RIG - any power-driven percussion, rotary, boring, coring, digging, jetting, or augering machine used in the construction of a well or borehole.

EMERGENCY SITUATION - any situation where immediate action is required to protect life or property. Emergency status would also extend to any situation where life is not immediately threatened but action is needed immediately and it is not possible to contact the state engineer for approval. For example, it would be considered an emergency if a domestic well needed immediate repair over a weekend when the state engineer's offices are closed.

GRAVEL PACKED WELL - a well in which filter material such as sand and/or gravel is placed in the annular space between the well intakes (screen or perforated casing) and the borehole wall to increase the effective diameter of the well and to prevent fine-grained sediments from entering the well.

GROUNDWATER - subsurface water in a zone of saturation.

GROUT - a fluid mixture of Portland cement or bentonite with water of a consistency that can be forced through a pipe and placed as required. Upon approval, [V]various additives such as sand, bentonite, and hydrated lime may be included in the mixture to meet different requirements.

HYDRAULIC FRACTURING - the process whereby water or other fluid is pumped with sand under high pressure into a well to fracture and clean-out the [reservoir ]rock surrounding the well bore thus increasing the flow to the well.

MONITOR WELL - a well, as defined under "well" in this section, that is constructed for the purpose of determining water levels, monitoring chemical, bacteriological, radiological, or other physical properties of ground water or vadose zone water.

NATIONAL SANITATION FOUNDATION (NSF) - a voluntary third party consensus standards and testing entity established under agreement with the U. S. Environmental Protection Agency (EPA) to develop testing and adopt standards and certification programs for all direct and indirect drinking water additives and products.

Information may be obtained from: NSF, 3475 Plymouth Road, P O Box 1468, Ann Arbor, Michigan 48106.

NEAT CEMENT GROUT - cement conforming to the ASTM Standard C150 (standard specification of Portland cement), with no more than six gallons of water per 94 pound sack (one cubic foot) of cement of sufficient weight density of not less than15 lbs/gallon.

OPERATOR - a drill rig operator is an individual who works under the direct supervision of a licensed Utah Water Well Driller and who can be left in responsible charge to construct water wells using equipment that is under the direct control of the licensee.

PIEZOMETER - a tube or pipe, open at the bottom in groundwater, and sealed along its length, used to measure hydraulic head or water level in a geologic unit.

PITLESS ADAPTER OR UNIT - an assembly of parts designed for attachment to a well casing which allows buried pump discharge from the well and allows access to the interior of the well casing for installation or removal of the pump or pump appurtenances, while preventing contaminants from entering the well. Such devices protect the water and distribution lines from temperature extremes, permit extension of the casing above ground as required in Subsection R655-4-9.3.2 and allow access to the well, pump or system components within the well without exterior excavation or disruption of surrounding earth or surface seal.

POLLUTION - the alteration of the physical, thermal, chemical, or biological quality of, or the contamination of, any water that renders the water harmful, detrimental, or injurious to humans, animals, vegetation, or property, or to public health, safety, or welfare, or impairs the usefulness or the public enjoyment of the water for any or reasonable purpose.

POTABLE WATER - water supplied for human consumption, sanitary use, or for the preparation of food or pharmaceutical products which is free from biological, chemical, physical, and radiological impurities.

PRESSURE GROUTING - a process by which grout is confined within the drillhole or casing by the use of retaining plugs or packers and by which sufficient pressure is applied to drive the grout slurry into the annular space or zone to be grouted.

PRIVATE WATER PRODUCTION WELL - a privately owned well constructed to supply water for any purpose which has been approved by the state engineer (such as irrigation, stockwater, domestic, commercial, industrial, etc.).

PROBATION - A disciplinary action that may be taken by the state engineer that entails greater review and regulation of well drilling activities but which does not prohibit a well driller from engaging in the well drilling business or operating well drilling equipment.

PROVISIONAL WELL - authorization granted by the state engineer to drill under a pending, unapproved water right, change or exchange application; or for the purpose of determining characteristics of an aquifer, or the existence of a useable groundwater source. Water from a provisional well cannot be put to beneficial use until the application has been approved.

PUBLIC WATER SYSTEM SUPPLY WELL - a well, either publicly or privately owned, providing water for human consumption and other domestic uses which has at least 15 service connections or regularly serves an average of at least 25 individuals daily for at least 60 days out of the year. Public Water System Supply Wells are also regulated by the Division of Drinking Water in the Utah Department of Environmental Quality (Section R309 of the Utah Administrative Code).

PUMPING WATER LEVEL - the [elevation of the surface of the ]water level in a well after a period of pumping at a given rate.

REVOCATION - A disciplinary action that may be taken by the state engineer that rescinds the well driller's Utah Water Well Driller's License

SAND - a material having a prevalent grain size ranging from 2 millimeters to 0.06 millimeters.

SAND CEMENT GROUT - a grout consisting of equal parts of cement conforming to ASTM standard C150 and sand/aggregate with no more than six (6) gallons of water per 94 pound sack (one cubic foot) of cement.

STANDARD DIMENSION RATIO (SDR) - the ratio of average outside pipe diameter to minimum pipe wall thickness.

STATE ENGINEER - the director of the Utah Division of Water Rights or any employee of the Division of Water Rights designated by the state engineer to act in administering these rules.

STATIC LEVEL - stabilized water level in a non-pumped well beyond the area of influence of any pumping well.

SURETY BOND - an indemnity agreement in a sum certain and payable to the state engineer, executed by the licensee as principal and which is supported by the guarantee of a corporation authorized to transact business as a surety in the State of Utah.

SUSPENSION - A disciplinary action that may be taken by the state engineer that prohibits the well driller from engaging in the well drilling business or operating well drilling equipment as a registered operator for a definite period of time and /or until certain conditions are met.

TEST WELL - authorization granted by the state engineer to drill under a Non-production well approval for the purpose of determining characteristics of an aquifer, or the existence of a useable groundwater source. Water from a Test Well cannot be put to beneficial use.

TREMIE PIPE - a device that carries materials such as seal material, gravel pack, or formation stabilizer to a designated depth in a drill hole or annular space.

UNCONSOLIDATED FORMATION - loose, soft, incoherent rock material composed of sedimentary, igneous, or metamorphic rock which includes sand, gravel, and mixtures of sand and gravel. These formations are widely distributed and can possess good water storage and transmissivity characteristics.

UNHYDRATED BENTONITE - dry bentonite consisting primarily of granules, tablets, pellets, or chips that may be placed in a well or borehole in the dry state and hydrated in place by either formation water or by the addition of potable water into the well or borehole containing the dry bentonite. Unhydrated bentonite can be used for sealing and abandonment of wells.

VADOSE ZONE - the zone containing water under less than atmospheric pressure, including soil water, intermediate vadose water and capillary water. The zone extends from land surface to the zone of saturation or water table.

WATERTIGHT - a condition that does not allow the entrance, passage, or flow of water under normal operating conditions.

WELL - a horizontal or vertical excavation or opening into the ground made by digging, boring, drilling, jetting, augering, or driving or any other artificial method and left cased or open for utilizing or monitoring underground waters.

WELL DRILLER - any person who is licensed by the state engineer to construct water wells for compensation or otherwise. The licensed driller has total responsibility for the construction work in progress at the well drilling site.

WELL DRILLER BOND - A financial guarantee to the state engineer, in the form of a surety bond or cash bond, by which a licensed driller binds himself to pay the penal sum of $5,000 to the state engineer in the event of significant noncompliance with the Administrative Rules for Water Well Drillers.

WELL DRILLING - the act of drilling, constructing, deepening, replacing, repairing, renovating, [or deepening, ]cleaning, developing, or abandoning a well.

 

R655-4-3. Licenses and Registrations.

3.1 General.

3.1.1 Section 73-3-25 of the Utah Code requires every person that constructs a well in the state to obtain a license from the state engineer. Licenses and registrations are not transferable.

3.1.2 Any person found to be drilling a well without a valid well driller's license or operator's registration will be ordered to cease drilling by the state engineer. The order may be made verbally but must also be followed by a written order. The order may be posted at an unattended well drilling site. A person found drilling without a license will be subject to the state engineer's enforcement powers under Section 73-2-25 of the Utah Code (Related rules: Section R655-14 UAC) and subject to criminal prosecution[ed] under Section 73-3-26 of the Utah Code annotated, 1953.

3.2 Well Driller's License.

An applicant must meet the following requirements to become licensed as a Utah Water Well Driller:

3.2.1 Applicants must be 21 years of age or older.

3.2.2 Complete and submit the application form provided by the state engineer.

3.2.3 Pay the application fee approved by the state legislature.

[ 3.2.4 Provide documentation of at least two (2) years of full time prior water well drilling experience OR documentation of 15 wells constructed by the applicant under the supervision of a licensed well driller. A copy of the well log for each well constructed must be included. The documentation must also show the applicant's experience with each type of drilling rig to be listed on the license. Acceptable documentation will include registration with the Division of Water Rights, letters from licensed well drillers (Utah or other states), or a water well drilling license granted by another state, etc.

Successful completion of classroom study in geology, well drilling, map reading, and other related subjects may be substituted for up to, but not exceeding, 12 months of drilling experience, and for up to, but not exceeding, five (5) of the required drilled wells. The state engineer will determine the number of months of drilling experience and the number of drilled wells that will be credited for the classroom study.]

3.2.4 Provide documentation of experience according to the following standards:

3.2.4.1 Water well drillers shall provide documentation of at least two (2) years of full time prior water well drilling experience with a licensed driller in good standing OR documentation of sixteen (16) wells constructed by the applicant under the supervision of a licensed well driller in good standing.

3.2.4.2 Monitor well drillers shall provide documentation of at least two (2) years of full time prior monitor well drilling experience with a licensed driller in good standing OR documentation of thirty two (32) wells constructed by the applicant under the supervision of a licensed well driller in good standing.

3.2.4.3 Heating/cooling exchange and other non-production well drillers must provide documentation of at least six (6) months of full time prior well drilling experience with a licensed driller in good standing AND documentation of sixteen (16) well drilling projects constructed by the applicant under the supervision of a licensed well driller in good standing.

3.2.4.4 A copy of the well log for each well constructed must be provided. The documentation must also show the applicant's experience with each type of drilling rig to be listed on the license. Acceptable documentation will include registration with the Division of Water Rights, letters from licensed well drillers (Utah or other states), or a water well drilling license granted by another state, etc.

3.2.4.5 Successful completion of classroom study in geology, well drilling, map reading, and other related subjects may be substituted for up to, but not exceeding, twenty five percent of the required drilling experience, and for up to, but not exceeding, twenty five percent of the required drilled wells or well drilling projects. The state engineer will determine the number of months of drilling experience and the number of drilled wells that will be credited for the classroom study.

3.2.5 File a well driller bond in the sum of $5,000 with the Division of Water Rights payable to the state engineer. The well driller bond must be filed under the conditions and criteria described in Section 4-3.6.

3.2.6 Obtain a score of at least 70% on each of the written licensing examinations required and administered by the state engineer. The required examinations test the applicant's knowledge of:

a. The Administrative Rules for Water Well Drillers and Utah water law as it pertains to underground water;

b. The minimum construction standards established by the state engineer for water well construction;

c. Geologic formations and proper names used in describing underground material types;

d. Reading maps and locating points from descriptions based on section, township, and range;

e. Groundwater geology and the occurrence and movement of groundwater;

f. The proper operating procedures and construction methods associated with the various types of water well drilling rigs. (A separate test is required for each type of water well drilling rig to be listed on the license).

3.2.7 Demonstrate proficiency in resolving problem situations that might be encountered during the construction of a water well by passing an oral examination administered by the state engineer.

3.3 Drill Rig Operator's Registration.

An applicant must meet the following requirements to become registered as a drill rig operator:

3.3.1 Applicants must be 18 years of age or older.

3.3.2 Complete and submit the application form provided by the state engineer.

3.3.3 Pay the application fee approved by the state legislature.

3.3.4 Provide documentation of at least six (6) months of prior water well drilling experience with a licensed driller in good standing. The documentation must show the applicant's experience with each type of drilling rig to be listed on the registration. Acceptable documentation will include letters from licensed well drillers or registration as an operator in another state.

3.3.5 Obtain a score of at least 70% on a written examination of the minimum construction standards established by the state engineer for water well construction. The test will be provided to the licensed well driller by the state engineer. The licensed well driller will administer the test to the prospective operator and return it to the state engineer for scoring.

3.4 Conditional, Restricted, or Limited Licenses.

The state engineer may issue a restricted, conditional, or limited license to an applicant based on prior drilling experience.

3.5 Refusal to Issue a License or Registration.

The state engineer may, upon investigation and after a hearing, refuse to issue a license or a registration to an applicant if it appears the applicant has not had sufficient training or experience to qualify as a competent well driller or operator.

3.6 Falsified Applications.

The state engineer may, upon investigation and after a hearing, revoke a license or a registration in accordance with Section 5.6 if it is determined that the original application contained false or misleading information.

3.7[6] Well Driller Bond.

3.7[6].1 General

3.7[6].1.1. In order to become licensed and to continue licensure, a well driller must file a well driller bond in the form of a surety bond or cash bond, approved by the state engineer, in the sum of five thousand dollars ($5,000) with the Division of Water Rights, on a form provided by the Division, which is conditioned upon proper compliance with the law and these rules and which is effective for the licensing period in which the license is to be issued. The bond shall stipulate the obligee as the "Office of the State Engineer". The well driller bond is penal in nature and is designed to ensure compliance by the licensed well driller to protect the groundwater resource, the environment, and public health and safety. The bond may only be exacted by the state engineer for the purposes of investigating, repairing, or abandoning wells in accordance with applicable rules and standards. No other person or entity may initiate a claim against the well driller bond. Lack of a current and valid well driller bond shall be deemed sufficient grounds for denial of a driller's license. The well driller bond may consist of a surety bond or a cash bond as described below.

3.7[6].2 Surety Bonds.

3.7[6].2.1. The licensed well driller and a surety company or corporation authorized to do business in the State of Utah as surety shall bind themselves and their successors and assigns jointly and severally to the state engineer for the use and benefit of the public in full penal sum of five thousand dollars ($5,000). The surety bond shall specifically cover the licensee's compliance with the Administrative Rules for Water Well Drillers found in R655-4 of the Utah Administrative Code. Forfeiture of the surety bond shall be predicated upon a failure to drill, construct, repair, renovate, deepen, clean, develop, or abandon a regulated well in accordance with these rules (R655-4 UAC). The bond shall be made payable to the 'Utah State Engineer' upon forfeiture. The surety bond must be effective and exactable in the State of Utah.

3.7[6].2.2. The bond and any subsequent renewal certificate shall specifically identify the licensed individual covered by that bond. The licensee shall notify the state engineer of any change in the amount or status of the bond. The licensee shall notify the state engineer of any cancellation or change at least thirty (30) days prior to the effective date of such cancellation or change. Prior to the expiration of the 30-days notice of cancellation, the licensee shall deliver to the state engineer a replacement surety bond or transfer to a cash bond. If such a bond is not delivered, all activities covered by the license and bond shall cease at the expiration of the 30 day period. Termination shall not relieve the licensee or surety of any liability for incidences that occurred during the time the bond was in force.

3.7[6].2.3. Before the bond is forfeited by the licensed driller and exacted by the state engineer, the licensed driller shall have the option of resolving the noncompliance to standard either by personally doing the work or by paying to have another licensed driller do the work. If the driller chooses not to resolve the problem that resulted in noncompliance, the entire bond amount of five thousand dollars ($5,000) shall be forfeited by the surety and expended by the state engineer to investigate, repair or abandon the well(s) in accordance with the standards in R655-4 UAC. Any excess there from shall be retained by the state engineer and expended for the purpose of investigating, repairing, or abandoning wells in accordance with applicable rules and standards. All claims initiated by the state engineer against the surety bond will be made in writing.

3.7[6].2.4. The bond of a surety company that has failed, refused or unduly delayed to pay, in full, on a forfeited bond is not approvable.

3.7[6].3 Cash Bonds.

3.7[6].3.1. The requirements for the well driller bond may alternatively be satisfied by a cash bond in the form of a certificate of deposit (CD) for the amount of five thousand dollars ($5,000) issued by a federally insured bank or credit union with an office(s) in the State of Utah. The cash bond must be in the form of a CD. Savings accounts, checking accounts, letters of credit, etc., are not acceptable cash bonds. The CD shall specifically identify the licensed individual covered by that fund. The CD shall be automatically renewable and fully assignable to the state engineer. CD shall state on its face that it is automatically renewable.

3.7[6].3.2. The cash bond shall specifically cover the licensee's compliance with well drilling rules found in R655-4 of the Utah Administrative Code. The CD shall be made payable or assigned to the state engineer and placed in the possession of the state engineer. If assigned, the state engineer shall require the bank or credit union issuing the CD to waive all rights of setoff or liens against those CD. The CD, if a negotiable instrument, shall be placed in the state engineer's possession. If the CD is not a negotiable instrument, the CD and a withdrawal receipt, endorsed by the licensee, shall be placed in the state engineer's possession.

3.7[6].3.3. The licensee shall submit CDs in such a manner which will allow the state engineer to liquidate the CD prior to maturity, upon forfeiture, for the full amount without penalty to the state engineer. Any interest accruing on a CD shall be for the benefit of the licensee.

3.7[6].3.4. The period of liability for a cash bond is five (years) after the expiration, suspension, or revocation of the license. The cash bond will be held by the state engineer until the five year period is over, then it will be relinquished to the licensed driller. In the event that a cash bond is replaced by a surety bond, the period of liability, during which time the cash bond will be held by the state engineer, shall be five (5) years from the date the new surety bond becomes effective.

3.7[6].4 Exacting a Well Driller Bond.

3.7[6].4.1. If the state engineer determines, following an investigation and a hearing in accordance with the process defined in Section 4-5, that the licensee has failed to comply with the Administrative Rules for Water Well Drillers and refused to remedy the noncompliance, the state engineer may suspend or revoke a well driller's license and fully exact the well driller bond and deposit the money as a non-lapsing dedicated credit.

3.7[6].4.2. The state engineer may expend the funds derived from the bond to investigate or correct any deficiencies which could adversely affect the public interest resulting from non-compliance with the Administrative Rules by any well driller.

3.7[6].4.3. The state engineer shall send written notification by certified mail, return receipt requested, to the licensee and the surety on the bond, if applicable, informing them of the determination to exact the well driller bond. The state engineer's decision regarding the noncompliance will be attached to the notification which will provide facts and justification for bond exaction. In the case of a surety bond exaction, the surety company will then forfeit the total bond amount to the state engineer. In the case of a cash bond, the state engineer will cash out the CD. The exacted well driller bond funds may then be used by the state engineer to cover the costs of well investigation, repair, and/or abandonment.

 

R655-4-4. Administrative Requirements and General Procedures.

4.1 Authorization to Drill.

The well driller shall make certain that a valid authorization or approval to drill exists before [beginning]engaging in regulated well drilling activity[or work on a well]. Authorization to drill shall consist of a valid 'start card' based on any of the approvals listed below. Items 4.1.1 through 4.1.12[11] allow the applicant to contract with a well driller to drill, construct, deepen, replace, repair, renovate, clean, develop, or abandon exactly one well at each location listed on the start card or approval form. The drilling of multiple borings/wells at an approved location/point of diversion is not allowed without authorization from the state engineer's office. Most start cards list the date when the authorization to drill expires. If the expiration date has passed, the start card and authorization to engage in regulated drilling activity is no longer valid. If there is no expiration date on the start card, the driller must contact the state engineer's office to determine if the authorization to drill is still valid. When the work is completed, the permission to drill is terminated.

4.1.1 An approved application to appropriate.

4.1.2 A provisional well approval letter.

An approved provisional well letter grants authority to drill but allows only enough water to be diverted to determine the characteristics of an aquifer or the existence of a useable groundwater source.

4.1.3 An approved permanent change application.

4.1.4 An approved exchange application.

4.1.5 An approved temporary change application.

4.1.6 An approved application to renovate or deepen an existing well.

4.1.7 An approved application to replace an existing well.

4.1.8 An approved monitor well letter.

An approved monitor well letter grants authority to drill but allows only enough water to be diverted to monitor groundwater.

4.1.9 An approved heat exchange well letter.

4.1.10 An approved cathodic protection well letter.

4.1.11 An approved non-production well construction application.

4.1.12[11] Any letter or document from the state engineer directing or authorizing a well to be drilled or work to be done on a well.

4.2 Start Cards.

4.2.1 Prior to commencing any work (other than abandonment, see 4.2.4) on any well governed by these administrative rules, the driller must notify the state engineer of that intention by transmitting the information on the "Start Card" to the state engineer by telephone, by facsimile (FAX), by hand delivery, or by e-mail. A completed original Start Card must be sent to the state engineer by the driller after it has been telephoned or E-mailed.

4.2.2 A specific Start Card is printed for each well drilling approval and is furnished by the state engineer to the applicant or the well owner. The start card is preprinted with the water right or non-production well number[/provisional/monitor well number], owner name/address, and the approved location of the well. The state engineer marks the approved well drilling activity on the card. The driller must put the following information on the card:

a. The date on which work on the well will commence;

b. The projected completion date of the work;

c. The well driller's license number;

d. The well driller's signature.

4.2.3 When a single authorization is given to drill wells at more than one point of diversion, a start card shall be submitted for each location to be drilled.

4.2.4 Following the submittal of a start card, if the actual start date of the drilling activity is postponed beyond the date identified on the start card, the licensed driller must notify the state engineer of the new start date.

4.2.5[4] A start card is not required to abandon a well. However, prior to commencing well abandonment work, the driller is required to notify the state engineer by telephone, by facsimile, or by e-mail of the proposed abandonment work. The notice must include the location of the well. The notice should also include the water right or non-production well number associated with the well and the well owner if that information is available.

4.3 General Requirements During Construction.

4.3.1 The well driller shall have the required penal bond continually in effect during the term of the well driller's license.

4.3.2 The well driller's license number or the well driller's company name exactly as shown on the well drilling license must be prominently displayed on each well drilling rig operated under the well driller's license. If the well driller's company name is changed the well driller must immediately inform the state engineer of the change in writing.

4.3.3 A licensed well driller or a registered operator must be at the well site whenever the following aspects of well construction are in process: advancing the borehole, setting casing and screen, placing a filter pack, constructing a surface seal, or similar activities involved in well deepening, renovation, [or ]repair, cleaning, developing, or abandoning[ a well]. All registered operators working under a well driller's license must be employees of the well driller and must use equipment either owned by or leased by the licensed well driller.

4.3.4 A registered operator who is left in responsible charge of advancing the borehole, setting casing and screen, placing a filter pack, constructing a surface seal, or similar activities involved in well deepening, renovation, [or ]repair, cleaning, developing, or abandoning [a well ]must have a working knowledge of the minimum construction standards and the proper operation of the drilling rig. The licensed well driller is responsible to ensure that a registered operator is adequately trained to meet these requirements.[ If, during a field inspection by the staff of the Division of Water Rights, it is determined that a registered operator in responsible charge does not meet these requirements, a state engineer's red tag (see Section 4.3.5) will be placed on the drilling rig and the drilling operation will be shut down. The order to cease work will remain effective until a qualified person is available to perform the work.

4.3.5 The state engineer or staff of the Division of Water Rights may order that work cease on the construction, repair, or abandonment of a well if a field inspection reveals that the construction does not meet the minimum construction standards to the extent that the public interest might be adversely affected. A cease work order may also be issued if the well driller is not licensed for the drilling method being used for the well construction. The state engineer's order will be in the form of a red tag which will be attached to the drilling rig. A letter from the state engineer will be sent to the licensed driller to explain the sections of the administrative rules which were violated. The letter will also explain the requirements that must be met before the order can be lifted.]

4.3.5 State engineer provisions for issuing cease and desist orders (Red Tags)

4.3.5.1 Construction Standards: The state engineer or staff of the Division of Water Rights may order that regulated work on a well cease if a field inspection reveals that the construction does not meet the minimum construction standards to the extent that the public interest might be adversely affected.

4.3.5.2 Licensed Drilling Method: A cease work order may also be issued if the well driller is not licensed for the drilling method being used for the well construction.

4.3.5.3 Incompetent Registered Operator: If, during a field inspection by the staff of the Division of Water Rights, it is determined that a registered operator in responsible charge does not meet these requirements, a state engineer's red tag (see Section 4.3.5) will be placed on the drilling rig and the drilling operation will be ordered to shut down. The order to cease work will remain effective until a qualified person is available to perform the work.

4.3.5.4 No licensed driller or registered operator on site: If, during a field inspection by the staff of the Division of Water Rights, it is determined that neither a licensed driller or registered operator are one site when regulated drilling activity is occurring, the state engineer may order regulated well drilling work to cease.

4.3.5.5 General: The state engineer's order will be in the form of a red tag which will be attached to the drilling rig. A letter from the state engineer will be sent to the licensed driller to explain the sections of the administrative rules which were violated. The letter will also explain the requirements that must be met before the order can be lifted.

4.3.6 When required by the state engineer, the well driller or registered operator shall take lithologic samples at the specified intervals and submit them in the bags provided by the state engineer.

4.3.7 A copy of the current Administrative Rules for Water Well Drillers should be available at each well construction site for review by the construction personnel. Licensed well drillers and registered operators must have proof of licensure or registration with them on site during regulated drilling activity.

4.3.8 Prior to starting construction of a new well, the licensed driller shall investigate and become familiar with the drilling conditions, geology of potential aquifers and overlying materials, anticipated water quality problems, and know contaminated water bearing zones that may be encountered in the area of the proposed drilling activity.

4.4 Removing Drill Rig From Well Site.

4.4.1 A well driller shall not remove his drill rig from a well site unless the well drilling activity is properly completed or abandoned in accordance with the construction standards in Sections 9 thru 12.[ Completion of a well shall include all surface seals, gravel packs, or curbs required.]

4.4.2 For the purposes of these rules, the regulated[construction, repair or abandonment ]work on a well will be considered completed when the well driller removes his drilling rig from the well site.

[4.4.3 The well driller may request a variance from the state engineer. The written request must indicate that the well has been temporarily abandoned as provided in Section R655-4-12 and must give the date when the well driller plans to continue work.]4.4.3 The well driller may request a variance from the state engineer to remove a drill rig from a well prior to completion or abandonment. This request must be in written form to the state engineer. The written request must provide justification for leaving the well incomplete or un-abandoned and indicate how the well will be temporarily abandoned as provided in Section R655-4-12 and must give the date when the well driller plans to continue work to either complete the well or permanently abandon it.

4.5 Official Well Driller's Report (Well Log).

4.5.1 Within 30 days of the completion of regulated work on any well, the driller shall file an official well driller's report (well log) with the state engineer. The blank well log form will be mailed to the licensed well driller upon receipt of the information on the Start Card as described in Subsection 4.2.

4.5.2 The water right number or non-production well [/provisional/monitor well ]number, owner name/address, and the approved location of the well will be preprinted on the blank well log provided to the well driller. The driller is required to verify this information and make any necessary changes on the well log prior to submittal. The state engineer will mark the approved activity (e.g., new, replace, repair, deepen) on the well log. The driller must provide the following information on the well log:

a. The start and completion date of work on the well;

b. The nature of use for the well (e.g., domestic, irrigation, stock watering, commercial, municipal, provisional, monitor, cathodic protection, heat pump, etc.;

c. The borehole diameter, depth interval, drilling method and drilling fluids utilized to drill the well;

d. The lithologic log of the well based on strata samples taken from the borehole as drilling progresses;

e. Static water level information to include date of measurement, static level, measurement method, reference point, artesian flow and pressure, and water temperature;

f. The size, type, description, joint type, and depth intervals of casing, screen, and perforations;

g. A description of the filter pack, surface and interval seal material, and packers used in the well along with necessary related information such as the depth interval, quantity, and mix ratio;

h. A description of the finished wellhead configuration;

i. The date and method of well development;

j. The date, method, yield, drawdown, and elapsed time of a well yield test;

k. A description of pumping equipment (if available);

l. Other comments pertinent to the well activity completed;

m. The well driller's statement to include the driller name, license number, signature, and date.

4.5.3 Accuracy and completeness of the submitted well log are required. Of particular importance is the lithologic section which should accurately reflect the geologic strata penetrated during the drilling process. Sample identification must be logged in the field as the borehole advances and the information transferred to the well log form for submission to the state engineer.

4.5.4 An amended well log shall be submitted by the licensed driller if it becomes known that the original report contained inaccurate or incorrect information, or if the original report requires supplemental data or information. Any amended well log must be accompanied by a written statement, signed and dated by the licensed well driller, attesting to the circumstances and the reasons for submitting the amended well log.

4.6 Official Well Abandonment Reports (Abandonment Logs).

4.6.1 Whenever a well driller is contracted to replace an existing well under state engineer's approval, it shall be the responsibility of the well driller to inform the well owner that it is required by law to permanently abandon the old well in accordance with the provisions of Section R655-4-12.

4.6.2 Within 30 days of the completion of abandonment work on any well, the driller shall file an abandonment log with the state engineer. The blank abandonment log will be mailed to the licensed well driller upon notice to the state engineer of commencement of abandonment work as described in Subsection R655-4-4(4.2.4).

4.6.3 The water right number or non-production well [/provisional/monitor well ]number, owner name/address, and the well location (if available) will be preprinted on the blank abandonment log provided to the well driller. The driller is required to verify this information and make any necessary changes on the abandonment log prior to submitting the log. The driller must provide the following information on the abandonment log:

a. Existing well construction information;

b. Date of abandonment;

c. Reason for abandonment;

d. A description of the abandonment method;

e. A description of the abandonment materials including depth intervals, material type, quantity, and mix ratio;

f. Replacement well information (if applicable);

g. The well driller's statement to include the driller

name, license number, signature, and date.

4.6.4 When a well is replaced and the well owner will not allow the driller to abandon the existing well, the driller must briefly explain the situation on the abandonment form and submit the form to the state engineer within 30 days of completion of the replacement well.

4.7 Incomplete or Incorrectly Completed Reports.

An incomplete well/abandonment log or a well/abandonment log that has not been completed correctly will be returned to the licensed well driller to be completed or corrected. The well log will not be considered filed with the state engineer until it is complete and correct.

4.8 Extensions of Time.

The well driller may request an extension of time for filing the well log if there are circumstances which prevent the driller from obtaining the necessary information before the expiration of the 30 days. The extension request must be submitted in writing before the end of the 30-day period.

4.9 Late Well Logs - Lapsed License

All outstanding well logs or abandonment logs shall be properly submitted to the state engineer prior to the lapsing of a license. A person with a lapsed license who has failed to submit all well/abandonment logs within 90 days of lapsing will be subject to the state engineer's enforcement powers under Section 73-2-25 of the Utah Code (Related rules: Section R655-14 UAC)

 

[R655-4-5. Infractions of the Administrative Requirements and the Minimum Construction Standards.

5.1 List of Infractions and Points.

Licensed well drillers who commit the infractions listed below in Table 1 shall have assessed against their well drilling record the number of points assigned to the infraction.

 

TABLE 1

Infractions of Administrative Requirements

                                                    Points

Start Cards/Authorization

Failure to properly notify the

  state engineer before the

  proposed start date shown

  on the start card                                  20

Performing any well drilling activity without

  valid authorization (except in

  emergency situations)                             100



Well Logs

Intentionally making a material

  misstatement of fact in an official

  well driller's report or amended

  official well driller's report

  (well log)                                        100

Well log submitted late                              10



Well Abandonment

Well abandonment report submitted

  late                                               10



Licenses

Intentionally making a material

  misstatement of fact in the

  application for a well driller's

  license                                           100

Well driller license or well driller

  name not clearly posted on well

  drilling rig                                       10

Failing to notify the state engineer

  in a timely manner of a change in

  the well driller's company name                    10



Operators / Contract Drillers

Employing an operator who is not

  registered with the state                          75

Contracting out work to an

  unlicensed driller (using the

  unlicensed driller's rig) without

  prior written approval from the state              75

Infractions of Construction Standards / Conditions

                                                     Points



Approvals

Constructing a replacement well

  further than 150 ft from the

  original well without the

  authorization of an approved

  change application                                 50

Failing to comply with any conditions

  included on the well approval such as

  minimum or maximum depths, specified

  locations of perforations, etc.                    50

Using a method of drilling not listed

  on the well driller's license                      30

Performing any well construction

  activity in violation of a red tag

  cease work order                                  100



Casing

Using or attempting to use sub-standard

  well casing                                        50

Using improper casing joints                         40

Failure to extend well casing at least

  18" above ground                                   30



Surface Seals



Using improper products or procedures

  to install a surface seal                         100

Failure to seal off artesian flow on

  the outside of casing                             100

Failure to install surface seal to

  adequate depth based on formation type            100



Well Abandonment

Using improper procedures to abandon

  a well                                             50

Using improper products to abandon a

  well                                               50



Construction Fluids

Using water of unacceptable quality

  in the well drilling operation                     40

Using improper circulation materials                 30

Using an unacceptable mud pit                        20



Filter Packs

Failure to install filter pack properly              40

Failure to disinfect filter pack                     30



Well Completion

Failure to make well accessible to

  water level or pressure head   measurements        30

Failure to install casing annular seals,

  cap, and valving, and to control

  artesian flow                                      30

Removing the well drilling rig from

  the well site before completing the

  well or temporarily or permanently

  abandoning the well                                50



General

Failure to securely cover an

  unattended well during
construction                30

 

5.2 When Points Are Assessed.

Points will be assessed against a driller's record upon verification by the state engineer that an infraction has occurred. Points will be assessed at the time the state engineer becomes aware of the infraction regardless of when the infraction occurred.

5.3 Appeal of Infractions.

Well drillers may appeal each infraction in writing within 30 days of written notification by the state engineer.

5.4 Warning Letter.

When the number of points assessed against the well driller's record equals seventy-five (75) points, a warning letter will be sent to the well driller. The letter will notify the driller that if he continues to violate the administrative requirements or minimum construction standards contained in the Administrative Rules for Water Well Drillers, a hearing will be held to determine if his license should be suspended or revoked or the bond exacted. The letter will also describe the options available to the driller to delete points from the record as described in Subsection R655-4-5.7. A copy of the driller's infraction record will be included with the letter. In the event numerous points are assessed against the well drillers record so that the total surpasses seventy-five (75) and one hundred (100) points at the same time, no warning letter will be sent.

5.5 Notice of Agency Action.

5.5.1 When the number of points assessed against the well driller's record equals 100, a Notice of Agency Action (NAA) will be sent to the well driller. The NAA will set forth the alleged facts, provide an opportunity for a response from the well driller, and provide notice of the hearing scheduled to consider the issues. The hearing will be scheduled at least 10 days from the date the NAA is mailed. The NAA will indicate the date, time, and place of the hearing.

5.5.2 A NAA may also be sent and a hearing may also be convened as a result of a complaint filed by a well owner regardless of the total number of points shown on the well driller's record.

5.5.3 The purpose of the hearing will be to determine if disciplinary action is necessary regarding the water well driller's Utah Water Well License. The hearing will be conducted informally according to the rules adopted under Sections 63-46b-4 and 63-46b-5, Utah Code. The hearing will be recorded. At the hearing, testimony will be taken under oath regarding the alleged facts included in the NAA. Those providing testimony may include the water well driller, the well owner, Division of Water Rights staff, and others as deemed necessary. Evidence that is pertinent to the alleged facts may also be presented at the hearing. After considering the testimony and the evidence presented at the hearing, the State Engineer may determine either that there is no cause for action against the well driller's license or that disciplinary action is necessary. Disciplinary action may consist of probation, suspension, or revocation of the Utah Water Well License.

5.6 License Probation, Suspension or Revocation.

5.6.1 Probation will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe first time infractions of the administrative rules that are limited in number and less serious in their impact on the well owner and on the health of the aquifer. The probation period will generally last until the number of infraction points on the well driller's record is reduced below 70 through any of the options described in Subsection 4-5.7.

5.6.2 Suspension will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe repeated infractions of the administrative rules, or infractions that a pose serious threat to the health of the aquifer, or a well driller's apparent disregard for the administrative rules or the state's efforts to regulate water well drilling. Depending upon the number and severity of the rule infractions, the state engineer may elect to suspend a well driller license for a certain period of time and/or until certain conditions have been met by the well driller. In establishing the length of the suspension, the state engineer will generally follow the guideline that three infraction points is the equivalent of one day of suspension. A well driller whose license has been suspended will be prohibited from engaging in the well drilling business or operating well drilling equipment as a registered operator. License suspension may also result in the exaction of the Well Driller Bond as set forth in Subsection 4-3.6.4. A well driller whose license has been suspended is allowed to work as a helper under the direct, continuous, and on-site supervision of a licensed well driller or registered operator. If the suspension period extends beyond the expiration date of the water well license, the water well driller may not apply to renew the license until the suspension period has run and any conditions have been met. Once the suspension period has run and once any conditions have been met by the well driller, the suspension will be lifted and the driller will be notified that he/she may again engage in the well drilling business. The well driller will then be placed on probation until the number of infraction points on the well driller's record is reduced below 70 through any of the options described in Subsection 4-5.7.

5.6.3 Revocation will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe infractions of the administrative rules for which the well driller's Utah Water Well License has previously been suspended. A well driller whose license has been revoked will be prohibited from engaging in the well drilling business or operating well drilling equipment as a registered operator. License suspension may also result in the exaction of the Well Driller Bond as set forth in Subsection 4-3.6.4. A well driller whose license has been revoked is allowed to work as a helper under the direct, continuous, and on-site supervision of a licensed well driller or registered operator. A well driller whose water well license has been revoked may not make application for a new water well license for a period of two years from the date of revocation. After the revocation period has run, a well driller may make application for a new license as provided in Section R655-4-3. However, the well drilling experience required must be based on new experience obtained since the license was revoked.

5.7 Deleting Point from the Driller Record.

Points assessed against a well driller's record will remain on the record unless deleted through any of the following options:

5.7.1 Points will be deleted three years after the date when the infraction is noted by the state engineer and the points are assessed against the driller's record.

5.7.2 One half the points on the record will be deleted if the well driller is free of infractions for an entire year.

5.7.3 Thirty (30) points will be deleted for obtaining six (6) hours of approved continuing education credits in addition to the credits required to renew the water well driller's license. A driller may exercise this option only once each year.

5.7.4 Twenty (20) points will be deleted for taking and passing (with a minimum score of 70%) the test covering the administrative requirements and the minimum construction standards. A driller may exercise this option only every other year.

5.8 Lack of Knowledge Not an Excuse.

Lack of knowledge of the law or the administrative requirements and minimum construction standards related to well drilling shall not constitute an excuse for violation thereof.

5.9 Misdemeanors.

Section 73-3-26 of the Utah Code annotated, 1953, classifies certain actions as class B Misdemeanors. Each day that a violation continues is a separate offense.

 

]R655-4-5. Well Driller Disciplinary Procedures.

5.1 Well driller disciplinary procedures will be conducted informally and are governed by Sections 63-46b-4 (Designation of Adjudicative Proceedings as Informal) and 63-46b-5 (Procedures for Informal Adjudicative Proceedings) of the Utah Code and by Section R655-6 (Administrative Procedures for Informal Proceedings Before the Division of Water Rights) of the Utah Administrative Code.

5.2 List of Infractions and Points.

Licensed well drillers who commit the infractions listed below in Table 1 shall have assessed against their well drilling record the number of points assigned to the infraction.

 

TABLE 1

Level I Infractions of Administrative Requirements

                                                    Points

Well log submitted late                              10

Well abandonment report submitted

  late                                               10

Well driller license or well driller

  name not clearly posted on well

  drilling rig                                       10

Failing to notify the state engineer

  of a change in  the well

  driller's company name                             10

Failure to properly notify the

  state engineer before the

  proposed start date shown

  on the start card                                  20

Failure to notify the state engineer

   of a change of start date                         50

Constructing a replacement well

  further than 150 ft from the

  original well without the

  authorization of an approved

  change application                                 50

Failure to drill at the state engineer

  approved location as identified

  on the start card                                  50

Removing the well drilling rig from

  the well site before completing the

  well or temporarily or permanently

  abandoning the well                                50

 

TABLE 2

Level II Infractions of Administrative Requirements

                                                    Points

Employing an operator who is not

  registered with the state                          75

Contracting out work to an

  unlicensed driller (using the

  unlicensed driller's rig) without

  prior written approval from the state              75

Performing any well drilling activity without

  valid authorization (except in

  emergency situations)                             100

Intentionally making a material

  misstatement of fact in an official

  well driller's report or amended

  official well driller's report

  (well log)                                        100

 

TABLE 3

Level III Infractions of Construction Standards / Conditions

                                                     Points

Approvals

Using a method of drilling not listed

  on the well driller's license                      30

Failing to comply with any conditions

  included on the well approval such as

  minimum or maximum depths, specified

  locations of perforations, etc.                    50

Performing any well construction

  activity in violation of a red tag

  cease work order                                  100



Casing

Failure to extend well casing at least

  18" above ground                                   30

Failure to install a protective casing

  around a PVC well at the surface                   50

Using improper casing joints                        100

Using or attempting to use sub-standard

  well casing                                       100



Surface Seals

Using improper products or procedures

  to install a surface seal                         100

Failure to seal off artesian flow on

  the outside of casing                             100

Failure to install surface seal to

  adequate depth based on formation type            100

Failure to install interval seals to

  eliminate aquifer commingling

  or cross contamination                            100



Well Abandonment

Using improper procedures to abandon

  a well                                            100

Using improper products to abandon a

  well                                              100



Construction Fluids

Using water of unacceptable quality

  in the well drilling operation                     40

Using an unacceptable mud pit                        40

Failure to use treated or disinfected

  water for drilling processes                       40

Using improper circulation materials

  or drilling chemicals                              100



Filter Packs

Failure to disinfect filter pack                     40

Failure to install filter pack properly              75



Well Completion

Failure to make well accessible to

  water level or pressure head measurements          30

Failure to install casing annular seals,

  cap, and valving, and to control

  artesian flow                                      30

Failure to disinfect a well upon

  completion of well drilling activity               40

Failure to install a pitless adapter

  according to standard                              75

Failure to develop and test a well

  according to standard                              75



General

Failure to securely cover an

  unattended well during construction                30

Failure to engage in well drilling

  activity in accordance with accepted

  industry practices                                 100

 

5.3 When Points Are Assessed.

Points will be assessed against a driller's record upon verification by the state engineer that an infraction has occurred. Points will be assessed at the time the state engineer becomes aware of the infraction regardless of when the infraction occurred.

5.4 Appeal of Infractions.

Well drillers may appeal each infraction in writing within 30 days of written notification by the state engineer.

5.5 Warning Letter.

When the number of points assessed against the well driller's record equals seventy-five (75) points, a warning letter will be sent to the well driller. The letter will notify the driller that if he continues to violate the administrative requirements or minimum construction standards contained in the Administrative Rules for Water Well Drillers, a hearing will be held to determine if his license should be suspended or revoked or the bond exacted. The letter will also describe the options available to the driller to delete points from the record as described in Subsection R655-4-5.7. A copy of the driller's infraction record will be included with the letter. In the event numerous points are assessed against the well drillers record so that the total surpasses seventy-five (75) and one hundred (100) points at the same time, no warning letter will be sent.

5.6 Well Driller Hearings.

5.6.1 When the number of points assessed against the well driller's record equals 100, a Notice of Agency Action (NAA) will be sent to the well driller. The NAA will set forth the alleged facts, provide an opportunity for a response from the well driller, and provide notice of the hearing scheduled to consider the issues. The hearing will be scheduled at least 10 days from the date the NAA is mailed. The NAA will indicate the date, time, and place of the hearing.

5.6.2 A NAA may also be sent and a hearing may also be convened as a result of a complaint filed by a well owner regardless of the total number of points shown on the well driller's record.

5.6.3 A NAA may be sent and a hearing may be convened if there is evidence that a license or registration application submitted to the state engineer contains intentionally false or misleading information.

5.6.4 The purpose of the hearing will be to determine if disciplinary action is necessary regarding the water well driller's Utah Water Well License. The hearing will be recorded. At the hearing, testimony will be taken under oath regarding the alleged facts included in the NAA. Those providing testimony may include the water well driller, the well owner, Division of Water Rights staff, and others as deemed necessary. Evidence that is pertinent to the alleged facts may also be presented at the hearing. After considering the testimony and the evidence presented at the hearing, the State Engineer may determine either that there is no cause for action against the well driller's license or that disciplinary action is necessary.

5.7 Administrative Penalties.

Administrative penalties ordered against a licensed driller by the state engineer following a hearing can include probation, administrative fines, license suspension, and license revocation. Administrative penalties are ordered based on the severity of the infraction (Level I, II, III from Table 1 of Section 5.1) as well as the recurrence of an infraction.

5.7.1 Level I Administrative Penalties: Level I administrative penalties will be levied against Level I administrative infractions (see Table 1 of Section 5.1). The Level I administrative penalty structure is as follows:

5.7.1.1 At the first conviction of Level I infractions, the disciplinary action for the infractions shall be probation.

5.7.1.2 Second conviction shall result in probation and a fine at a rate of $2.50 per infraction point.

5.7.1.3 Third conviction shall result in probation and an elevated fine at a rate of $5.00 per infraction point.

5.7.1.4 Fourth conviction shall result in an elevated fine at a rate of $10.00 per infraction point and possible suspension.

5.7.1.5 Continued and repeated convictions beyond the fourth conviction may result in an elevated fine at a rate of $10.00 per infraction point and possible suspension or revocation.

5.7.1.6 Fines for late well logs and abandonment logs shall be calculated separately and added to fines calculated for other infractions. For late well log infractions, the points associated with each infraction will be multiplied by a factor based on the lateness of the well log. The infraction point multipliers are as follows:

 

TABLE 4

Tardiness of the log            Infraction Point Multiplier

   1-2 weeks                                    0.50

   2-4 weeks                                    1.00

   1-3 months                                   1.50

   3-6 months                                   2.00

   6-9 months                                   2.50

   9-12 months                                  3.00

   Over 12 months                               4.00

 

5.7.2 Level II Administrative Penalties: Level II administrative penalties will be levied against Level II administrative infractions (see Table 2 of Section 5.1). The Level II administrative penalty structure is as follows:

5.7.2.1 At the first conviction of Level II infractions, the disciplinary action shall result in probation and a fine at a rate of $2.50 per infraction point.

5.7.2.2 Second conviction shall result in probation and an elevated fine at a rate of $5.00 per infraction point.

5.7.2.3 Third conviction shall result in possible suspension and an elevated fine at a rate of $10.00 per infraction point.

5.7.2.4 Continued and repeated convictions beyond the fourth conviction may result in an elevated fine at a rate of $10.00 per infraction point and possible suspension or revocation.

5.7.3 Level III Administrative Penalties: Level III administrative penalties will be levied against Level III construction infractions (see Table 3 of Section 5.1). The Level III administrative penalty structure is as follows:

5.7.3.1 At the first conviction of Level III infractions, the disciplinary action shall result in probation and a fine at a rate of $5.00 per infraction point.

5.7.3.2 Second conviction shall result in possible suspension and an elevated fine at a rate of $10.00 per infraction point.

5.7.3.3 Third conviction may result in an elevated fine at a rate of $10.00 per infraction point and possible suspension or revocation.

5.7.4 Administrative Penalties - General

5.7.4.1 Penalties will only be imposed as a result of a well driller hearing.

5.7.4.2 Failure to pay a fine within 30 days from the date it is assessed will result in the suspension of the well driller license until the fine is paid.

5.7.4.3 Fines shall be deposited as a dedicated credit. The state engineer shall expend the money retained from fines for expenses related to well drilling activity inspection, well drilling enforcement, and well driller education.

5.7.5 Probation: As described above in Sections 5.7.1, 5.7.2, and 5.7.3, probation will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe first time infractions of the administrative rules that are limited in number and less serious in their impact on the well owner and on the health of the aquifer. The probation period will generally last until the number of infraction points on the well driller's record is reduced below 70 through any of the options described in Subsection 4-5.8.

5.7.6 Suspension: Suspension will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe repeated convictions of the administrative rules, or infractions that a pose serious threat to the health of the aquifer, or a well driller's apparent disregard for the administrative rules or the state's efforts to regulate water well drilling. Depending upon the number and severity of the rule infractions as described above in Sections 5.7.1, 5.7.2, and 5.7.3, the state engineer may elect to suspend a well driller license for a certain period of time and/or until certain conditions have been met by the well driller. In establishing the length of the suspension, the state engineer will generally follow the guideline that three infraction points is the equivalent of one day of suspension. A well driller whose license has been suspended will be prohibited from engaging in regulated well drilling activity. License suspension may also result in the exaction of the Well Driller Bond as set forth in Subsection 4-3.7.4. A well driller whose license has been suspended is allowed to work as a registered operator under the direct, continuous supervision of a licensed well driller. If the suspension period extends beyond the expiration date of the water well driller license, the water well driller may not apply to renew the license until the suspension period has run and any conditions have been met. Once the suspension period has run and once all conditions have been met by the well driller, the suspension will be lifted and the driller will be notified that he/she may again engage in the well drilling business. The well driller will then be placed on probation until the number of infraction points on the well driller's record is reduced below 70 through any of the options described in Subsection 4-5.8.

5.7.7 Revocation: Revocation will generally be the disciplinary action imposed in situations where the facts established through testimony and evidence describe repeated convictions of the administrative rules for which the well driller's Utah Water Well License has previously been suspended. Revocation will also be the disciplinary action taken if after a hearing the facts establish that a driller knowingly provided false or misleading information on a driller license application. A well driller whose license has been revoked will be prohibited from engaging in regulated well drilling activity. License revocation may also result in the exaction of the Well Driller Bond as set forth in Subsection 4-3.7.4. A well driller whose license has been revoked is allowed to work as a registered operator under the direct, continuous supervision of a licensed well driller. A well driller whose water well license has been revoked may not make application for a new water well license for a period of two years from the date of revocation. After the revocation period has run, a well driller may make application for a new license as provided in Section R655-4-3. However, the well drilling experience required must be based on new experience obtained since the license was revoked.

5.8 Deleting Point from the Driller Record.

Points assessed against a well driller's record will remain on the record unless deleted through any of the following options:

5.8.1 Points will be deleted three years after the date when the infraction is noted by the state engineer and the points are assessed against the driller's record.

5.8.2 One half the points on the record will be deleted if the well driller is free of infractions for an entire year.

5.8.3 Thirty (30) points will be deleted for obtaining six (6) hours of approved continuing education credits in addition to the credits required to renew the water well driller's license. A driller may exercise this option only once each year.

5.8.4 Twenty (20) points will be deleted for taking and passing (with a minimum score of 70%) the test covering the administrative requirements and the minimum construction standards. A driller may exercise this option only every other year.

5.9 Lack of Knowledge Not an Excuse.

Lack of knowledge of the law or the administrative requirements and minimum construction standards related to well drilling shall not constitute an excuse for violation thereof.

 

R655-4-6. Renewal of Well Driller's License and Operator's Registration.

6.1 Well Driller's Licenses.

6.1.1 Water well driller licenses shall expire and be renewed according to the following provisions:[

a. Between January 1, 2004 and June 30, 2006 water well driller licenses shall expire and be renewed according to the following schedule:

1. The licenses of water well drillers whose last name begins with A thru L shall not expire on December 31, 2004 but shall expire at 12 midnight on June 30, 2005. The continuation of the license will depend on documentation of a valid $5,000 well driller bond for the period thru June 30, 2005. Well drillers whose licenses expire on June 30, 2005 and who meet the application requirements of R655-4-6(6.1.2) including the documentation of nine (9) continuing education credits, shall receive a license that expires on June 30, 2007.

2. The licenses of water well drillers whose last name begins with M thru Z shall expire at midnight on December 30, 2004. Well drillers whose last name begins with M thru Z and who meet the application requirements of R655-4-6(6.1.2) shall receive a license that expires on June 30, 2006. The $5,000 well driller bond must be valid for the period January 1, 2005 through June 30, 2006. Well drillers whose licenses expire on June 30, 2006 and who meet the application requirements of R655-4-6(6.1.2) including the documentation of nine (9) continuing education credits, shall receive a renewed license for the a 2 year period.]

a[b]. [After June 30, 2005, t]The licenses of well drillers whose last name begins with A thru L shall expire at 12 midnight on June 30 of odd numbered years.

b[c]. [After June 30, 2006, t]The licenses of well drillers whose last name begins with M thru Z shall expire at 12 midnight on June 30 of even numbered years.

c[d]. Drillers who meet the renewal requirements set forth in Subsection R655-4-6(6.1.2) on or before the expiration deadlines set forth in Subsection R655-4-6(6.1.1) shall be authorized to operate as a licensed well driller until the new license is issued.

d[e]. Drillers must renew their licenses within 24 months of the license expiration date. Drillers failing to renew within 24 months of the license expiration date must re-apply for a well driller's license, meet all the application requirements of Subsection R655-4-3(3.2), and provide documentation of 12 hours of continuing education according to the requirements of R655-4-6 (6.2) obtained within the previous 24 months.

6.1.2 Applications to renew a well driller's license must include the following items:

a. Payment of the license renewal fee determined and approved by the legislature;

b. Written application to the state engineer;

c. Documentation of continuing well driller bond coverage in the amount of five thousand dollars ($5,000) penal bond for the next licensing period calendar year. The form and conditions of well driller bond shall be as set forth in Section 4.3. Allowable documentation can include bond continuation certificates and CD statements;

d. Proper submission of all start cards, official well driller reports (well logs), and well abandonment reports for the current licensing period[calendar year];

e. Documentation of compliance with the continuing education requirements described in Section 6.2.1. Acceptable documentation of attendance at approved courses must include the following information: the name of the course, the date it was conducted, the number of approved credits, the name and signature of the instructor and the driller's name; for example, certificates of completion, transcripts, attendance rosters, diplomas, etc. (Note: drillers are advised that the state engineer will not keep track of the continuing education courses each driller attends during the year. Drillers are responsible to acquire and then submit documentation with the renewal application.)

6.1.3 License renewal applications that do not meet the requirements of Subsection R655-5-6(6.1.2) by June 30 of the expiration year or which are received after June 30 of the expiration year, will be assessed an additional administrative late fee determined and approved by the legislature.

6.1.4 The state engineer may renew a license on a restricted, conditional, or limited basis according to the driller's performance and compliance with established rules and construction standards. The state engineer my refuse to renew a license to a well driller if it appears that there has been a violation of these rules or a failure to comply with Section 73-3-25[2] of the Utah Code.

6.2 Continuing Education.

6.2.1 During each license period, licensed well drillers are required to earn at least twelve (12) continuing education credits by attending training sessions sponsored or sanctioned by the state engineer. Drillers who do not renew their licenses, but who intend to renew within the following 24 month period allowed in Section 6.1.1, are also required to earn twelve (12) continuing education credits.

6.2.2 The state engineer shall establish a committee consisting of the state engineer or a representative, no more than four licensed well drillers, a ground water scientist, and a manufacturer/supplier of well drilling products. The committee will develop criteria for the training courses, approve the courses which can offer continuing education credits, and assign the number of credits to each course. The committee will make recommendations to the state engineer concerning appeals from training course sponsors and well drillers related to earning continuing education credit.

6.2.3 The committee established in Section 6.2.2 shall assign the number of continuing education credits to each proposed training session based on the instructor's qualifications, a written outline of the subjects to be covered, and written objectives for the session. Well drillers wishing continuing education credit for other training sessions shall provide the committee with all information it needs to assign continuing education requirements.

6.2.4 Licensed drillers must complete a State Engineer-sponsored "Administrative Rules for Well Drillers" review course or other approved rules review once every four (4) years.

6.2.5 CE credits cannot be carried over from one licensing period to another.

6.3 Drill Rig Operator's Registration.

6.3.1 All operator's registrations shall expire at the same time as the license of the well driller by whom they are employed. Operators who meet the renewal requirements set forth in Subsection R655-4-6(6.3.2) on or before 12 midnight June 30 of the expiration year shall be authorized to act as a registered operator until the new registration is issued. Operators must renew their registrations within 24 months of the registration expiration date. Operators failing to renew within 24 months of the registration expiration date must re-apply for an operator's registration and meet all the application requirements of Subsection R655-4-3(3.3).

6.3.2 Applications to renew an operator's registration must include the following items:

a. Payment of the registration renewal fee determined and approved by the legislature;

b. Written application to the state engineer.

6.3.3 Registration renewal applications that do not meet the requirements of Subsection R655-4-6(6.3.2) by the June 30 expiration date or that are received after the June 30 expiration date will be assessed an additional administrative late fee determined and approved by the legislature.

 

R655-4-7. The Approval Process for Non-Production Wells[Cathodic Protection Wells, Heating, or Cooling Exchange Wells and Monitor Wells].

7.1 General.

[Only]Regulated non-production wells such as cathodic protection wells, heating or cooling exchange wells, and monitor wells drilled and constructed to a depth greater than[of] 30 feet [or greater ]below natural ground surface require approval from the state engineer.

7.2 Approval to Construct or Replace.

Approval to construct or replace non-production wells[cathodic protection wells, heating or cooling exchange wells, and monitor wells] is issued by the state engineer's regional offices following review of written requests from the owner or applicant, federal or state agency or engineering representative. The requests for approval shall be made on forms provided by the state engineer entitled "Request for Non-Production Well Construction". The following information must be included on the form:

a. General location or common description of the project.

b. Specific course and distance locations from established government surveyed outside section corners or quarter corners.

c. Total anticipated number of wells to be installed.

d. Diameters, approximate depths and materials used in the wells.

e. Projected start and completion dates.

f. Name and license number of the driller contracted to install the wells.

There is no fee required to request approval to drill a non-production wells[cathodic protection well, a heating or cooling exchange well, or a monitor well]. Upon written approval by the state engineer, the project will be assigned an approved [authorization]non-production well number which will be referenced on all start cards and official well driller's reports.

 

R655-4-8. General Requirements.

8.1 Standards.

8.1.1 In some locations, the compliance with the following minimum standards will not result in a well being free from pollution or from being a source of subsurface leakage, waste, or contamination of the groundwater resource. Since it is impractical to attempt to prepare standards for every conceivable situation, the well driller shall judge when to construct wells under more stringent standards when such precautions are necessary to protect the groundwater supply and those using the well in question. Other state and local regulations pertaining to well drilling and construction, groundwater protection, and water quality regulations may exist that are either more stringent than these rules or that specifically apply to a given situation. It is the well driller's responsibility to understand and apply other regulations as applicable.

8.2 Well Site Locations.

8.2.1 Well site locations are described by course and distance from outside section corners or quarter corners (based on a Section/Township/Range Cadastral System) and by the Universal Transverse Mercator (UTM) coordinate system on all state engineer authorizations to drill (Start Cards). However, the licensee should also be familiar with local zoning ordinances, or county boards of health requirements which may limit or restrict the actual well location and construction in relationship to property/structure boundaries and existing or proposed concentrated sources of pollution or contamination such as septic tanks, drain fields, sewer lines, stock corrals, feed lots, etc. The licensee should also be familiar with the Utah Underground Facilities Act (Title 54, Chapter 8a of the Utah Code Annotated 1953 as amended) which requires subsurface excavators (including well drilling) to notify operators of underground utilities prior to any subsurface excavation. Information on this requirement can be found by calling (800)662-4111.

8.2.2 Regulated wells shall be drilled at the approved location as defined on the valid start card. The driller shall check the drilling location to see if it [generally ]matches the state-approved location listed on the Driller's Start Card.[ If the actual drilling location is significantly different than the Start Card location, the driller shall indicate the difference on the Well Log.]

8.3 Unusual Conditions.

8.3.1 If unusual conditions occur at a well site and compliance with these rules and standards will not result in a satisfactory well or protection to the groundwater supply, a licensed water well driller shall request that special standards be prescribed for a particular well. The request for special standards shall be in writing and shall set forth the location of the well, the name of the owner, the unusual conditions existing at the well site, the reasons that compliance with the rules and minimum standards will not result in a satisfactory well, and the proposed standards that the licensed water well driller believes will be more adequate for this particular well. If the state engineer finds that the proposed changes are in the best interest of the public, he will approve the proposed changes by assigning special standards for the particular well under consideration.

 

R655-4-9. Well Drilling and Construction Requirements.

9.0 General.

9.0.1 Figures 1 through 5 are used to illustrate typical well construction standards, and can be viewed in the State of Utah Water Well Handbook available at the Division of Water Rights, 1594 West North Temple, Salt Lake City, Utah. Figure 1 illustrates the typical construction of a drilled well with driven casing such as a well drilled using the cable tool method or air rotary with a drill-through casing driver. Figure 2 illustrates the typical construction of a well drilled with an oversized borehole and/or gravel packed without the use of surface casing. Figure 3 illustrates the typical construction of a well drilled with an oversized borehole and/or gravel packed with the use of surface casing. Figure 4 illustrates the typical construction of a well drilled with an oversized borehole and/or gravel packed completed in stratified formations in which poor formation material or poor quality water is encountered. Figure 5 illustrates the typical construction of a well completed with PVC or nonmetallic casing.

9.1 Approved Products, Materials, and Procedures.

9.1.1 Any product, material or procedure designed for use in the drilling, construction, cleaning, renovation, development or abandonment of water or monitor wells, which has received certification and approval for its intended use by the National Sanitation Foundation (NSF) under ANSI/NSF Standard 60 or 61, the American Society for Testing Materials (ASTM), the American Water Works Association (AWWA) or the American National Standards Institute (ANSI) may be utilized. Other products, materials or procedures may also be utilized for their intended purpose upon manufacturers certification that they meet or exceed the standards or certifications referred to in this section and upon state engineer approval.

9.2 Well Casing - General

9.2.1 Drillers Responsibility. It shall be the sole responsibility of the well driller to determine the suitability of any type of well casing for the particular well being constructed, in accordance with these minimum requirements.

9.2.2 Casing Stick-up. The well casing shall extend a minimum of 18 inches above finished ground level and the natural ground surface should slope away from the casing. A secure sanitary, weatherproof seal or a completely welded cap shall be placed on the top of the well casing to prevent contamination of the well. If a vent is placed in the cap, it shall be properly screened to prevent access to the well by debris, insects, or other animals.

9.2.3 Steel Casing. All steel casing installed in Utah shall be in new or like-new condition, being free from pits or breaks, clean with all potentially dangerous chemicals or coatings removed, and shall meet the minimum specifications listed in Table [2]5 of these rules. In order to utilize steel well casing that does not fall within the categories specified in Table [2]5, the driller shall receive written approval from the state engineer. All steel casing installed in Utah shall meet or exceed the minimum ASTM, ANSI, or AWWA standards for steel pipe as described in Subsection 9.1 unless otherwise approved by the state engineer. Applicable standards (most recent revisions) may include:

ANSI/AWWA A100-AWWA Standard for Water Wells.

ANSI/ASTM A53-Standard Specifications for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless.

ANSI/ASTM A139-Standard Specification for Electric-Fusion (Arc)-Welded Steel Pipe (NPS 4 and over).[

ANSI/ASTM A606-Standard Specification for Steel, Sheet, and Strip, High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, with Improved Atmospheric Corrosion Resistance.]

ANSI/AWWA C200-Standard for Steel Water Pipe-6 in. and Larger.

API Spec.5L-Specification for Liner Pipe.

ASTM A106-Standard Specification for Seamless Carbon Steel Pipe for High Temperature Service

ASTM A778-Standard Specifications for Welded, Unannealed Austenitic Stainless Steel Tubular Products.

ASTM A252-Standard Specification for Welded and Seamless Steel Pipe Piles.

ASTM A312-Standard Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

 

TABLE [2]5
MINIMUM WALL THICKNESS FOR STEEL WELL CASING

Depth

             0   200   300   400   600    800   1000  
1500

Nominal     to    to    to    to    to     to     to    
to

Casing     200   300   400   600   800   1000   1500  
2000

Diameter  (ft)  (ft)  (ft)  (ft)  (ft)   (ft)   (ft)   (ft)

 2       .154  .154   .154  .154  .154   .154

 3       .216  .216   .216  .216  .216   .216

 4       .237  .237   .237  .237  .237   .237   .237   .237

 5       .250  .250   .250  .250  .250   .250   .250   .250

 6       .250  .250   .250  .250  .250   .250   .250   .250

 8       .250  .250   .250  .250  .250   .250   .250   .250

10       .250  .250   .250  .250  .250   .250   .312   .312

12